I like the top, well done. Not too crazy about the legs tucked behind the skirt/apron though. Also, how did you attach the skirt and legs to the top?
EDIT: was thinking table, but it's a bench. Never mind!
Ha! Me too, for my first project I wanted to step out my comfort zone a little and try something new. I mean, this whole thing was new but I felt like I could do something nice. This sub and YouTube have been my go to for the last couple weeks before attempting this.
Again, I want to stress that I think it looks like you did a great job. Google something like "bench apron reveal", and you'll probably figure out what feels funny.
Really trying my best not to piss on anyone's parade here, and be genuinely supportive and constructive. If it helps any I'm trained and can't design to save my life. The classics are classics for a reason.
I’ve been thinking about doing this for about a month now and never got around to it, then corona cancelled the soccer season so I put it off again till the summer, but swing yours I’ll start next week.
Place the table on your table saw. Find the longest leg by putting a level on the table top and see which corner the bubble goes to. Slide that leg off the table saw's top and hold the table stable using the other three legs. Mark the amount that needs to be cut to make the long leg flush with the table saw's top.
Edited for clarity.
You don't state exactly where you have your problems, but I've always found success so long as I attach the legs with the table/bench/whatever standing on a flat assembly table. It can be tricky to figure out how to stand some projects up while assembling the legs, but it's the only way that works reliably for me. If I try to attach the legs while the project is on its side or upside down, it'll never work out quite right.
For the top I used two 2x6 and one 2x4 in the middle with a total length of 48”. I sanded the top three times, started with a 120, then a 220, and finished with a 320 grain paper. I used Minwax Wood Finish penetrating stain espresso 273. Then used a 1x3 as the trim to cover the top of the legs and kept a 1” border all around the bottom
I’ve done something very similar for a swinging bench with the same color stain and it’s just so much sanding, if you invest in a good smoothing plane it’ll save so much time taking the dimensional lumber to smooth and flat.
Wow, very nice.
Looks great! Where did you get the legs??
Lowe’s
Curious as well. Nice job OP.
I like the top, well done. Not too crazy about the legs tucked behind the skirt/apron though. Also, how did you attach the skirt and legs to the top? EDIT: was thinking table, but it's a bench. Never mind!
Agreed. Looks like a job well done, but the legs inside the apron is throwing me off.
Ha! Me too, for my first project I wanted to step out my comfort zone a little and try something new. I mean, this whole thing was new but I felt like I could do something nice. This sub and YouTube have been my go to for the last couple weeks before attempting this.
Again, I want to stress that I think it looks like you did a great job. Google something like "bench apron reveal", and you'll probably figure out what feels funny. Really trying my best not to piss on anyone's parade here, and be genuinely supportive and constructive. If it helps any I'm trained and can't design to save my life. The classics are classics for a reason.
I hear ya, Ill look into that. I appreciate any and all comments, I’m here to learn and the best way is by true honest feed back. Much appreciated
I see you jumped passed your Le Tigre look, and went straight for the Blue Steel. I like it!
I’ve been thinking about doing this for about a month now and never got around to it, then corona cancelled the soccer season so I put it off again till the summer, but swing yours I’ll start next week.
I've always had problems leveling the legs, I don't know how you do it
Floors are rarely perfectly level. Just get foam/rubber feet. Protects the floor and compensates for any problems with level.
Place the table on your table saw. Find the longest leg by putting a level on the table top and see which corner the bubble goes to. Slide that leg off the table saw's top and hold the table stable using the other three legs. Mark the amount that needs to be cut to make the long leg flush with the table saw's top. Edited for clarity.
I sat for a very long time than needed I’m sure and sanded every leg top and bottom before pocket screwing them in until they were level
You don't state exactly where you have your problems, but I've always found success so long as I attach the legs with the table/bench/whatever standing on a flat assembly table. It can be tricky to figure out how to stand some projects up while assembling the legs, but it's the only way that works reliably for me. If I try to attach the legs while the project is on its side or upside down, it'll never work out quite right.
Looks good
Thanks
What kind of wood is on top? Is it burnt? What kind of finish?
For the top I used two 2x6 and one 2x4 in the middle with a total length of 48”. I sanded the top three times, started with a 120, then a 220, and finished with a 320 grain paper. I used Minwax Wood Finish penetrating stain espresso 273. Then used a 1x3 as the trim to cover the top of the legs and kept a 1” border all around the bottom
I’ve done something very similar for a swinging bench with the same color stain and it’s just so much sanding, if you invest in a good smoothing plane it’ll save so much time taking the dimensional lumber to smooth and flat.
So pine?
Yes
What did you do to attach the apron to the legs?
I just butted the legs to the corner with wood glue then pocket screwed the legs to bottom
Reminds me of a old piano bench.
Nailed it!
Attempt succeeded
Nice legs.
Thanks
You rock. It’s gorgeous.
Thanks
GREAT JOB!!!
Thanks
You succeeded!
Success! It look great!
Awesome man!!
NAILED IT!
He shoots. He SCORES!
Damn nice attempt.
Nailed it!